![]() The following formulas are used to estimate the maximum short-circuit current " Ik_max" for three-phase medium-voltage transformers. On the other hand, a typical application is the plausibility check of the parameters of the high current stage of a transformer protection relay during the commissioning or repeat protection test, for example with our relay test system ARTES. It must also be taken into account that typical protection current transformers used in medium voltage can transmit currents up to 40 times higher than the rated current of the transformer in the event of a short circuit. On the one hand, to be able to estimate the current carrying capacity of input circuits, such as in the KoCoS fault recorder system SHERLOG. In practice, the value of the maximum short-circuit current "I sc_max" of a transformer is often needed. Mantenimiento y pruebas a interruptores.Instalación y puesta en marcha de equipo secundario.Servicios y pruebas secundarias y a relevadores de protección.Mediciones de perfiles en obleas de silicio.The results showed that the films offer good corrosion resistance on the metal substrate, decreasing current densities up to one order of magnitude. The coating were characterized by X ray diffraction (XRD), scanning electron microscopy (SEM) and dispersive energy spectroscopy (EDX), X ray fluorescence (XRF) and adhesion measurements. The soles prepared were studied trough rheological, pH as a time function, Fourier Transform Infrared Spectroscopy (FTIR) and differential scanning calorimetry (DSC) analysis. The coatings were evaluated by potentiodynamic polarization and Electrochemical Impedance Spectroscopy (EIS) test in an electrolytic solution of 3.5% Wt NaCl + 0.5 M H 2SO 4. The soles were prepared from a mixture of organic precursors, such as 98% tetraethoxysilane (TEOS), titanium tetrabutoxide (TBT) 97%, Zirconium (IV) butoxide (TBZ) 80% in 1-butanol solution and bismuth penta nitrate-hydrate Bi (NO 3) 3*5H 2O. This report show the synthesis and corrosion resistance of SiO 2-TiO 2-ZrO 2-BiO 2 coatings deposited by spin-coating on AISI 316L stainless steel. ![]() Los resultados mostraron que las películas ofrecen una buena resistencia a la corrosión sobre el sustrato metálico disminuyendo los valores de densidades de corriente hasta en un orden de magnitud. Los recubrimientos se caracterizaron mediante difracción de rayos X (XRD), microscopia electrónica de barrido (MEB), espectroscopia de energías dispersivas (EDX), fluorescencia de rayos X (XRF) y medidas de adherencia. A los soles preparados se les caracterizó mediante estudio reológico, de pH en función del tiempo, mediciones de espectroscopia de infrarrojo por transformada de Fourier (FTIR) y calorimetría diferencial de barrido (DSC). La resistencia a la corrosión se determinó mediante ensayos de curvas de polarización potenciodinámica y de espectroscopia de impedancia electroquímica (EIS) en una solución electrolítica de 3,5% Wt de NaCl + 0,5 M de H 2SO 4. Los soles se prepararon a partir de una mezcla de precursores orgánicos, como el tetraetoxisilano (TEOS) al 98%, tetrabutóxido de titanio (TBT) al 97%, zirconio (IV) butóxido (TBZ) al 80% en solución 1-butanol y nitrato de bismuto penta-hidratado Bi(NO 3) 3*5H 2O. En este trabajo se presenta la síntesis y la evaluación de la resistencia a la corrosión de recubrimientos de SiO 2-TiO 2-ZrO 2-BiO 2 depositados por la técnica de centrifugado sobre acero inoxidable AISI 316L.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |